Lab 50
€117.80
Uni-tube design with unmatched performance, style and safety features. The Lab 50 is the 18500 version of our most innovative, hard-hitting mechanical mod.
The Lab 50 is a high-performance 18500 mech mod based on our robust uni-tube design. Picking up where the Roller and Dingo left off, the Lab is a sturdier, simpler and easier-to-use top-side-firing mech mod. With its refined, sturdy switch and absolute minimum number of body parts to fiddle with, the Lab is a high-efficiency device with performance and safety features unseen in current top-firing designs.
The simplicity, ease-of-use and performance of the Lab comes with a style that departs from the strict minimalism of the Roller and Dingo. The Lab has a slightly more aggressive form which is still minimal and ergonomic, in line with its unique character.
The Lab sets a new standard in mech mod performance and safety, since it has been designed to include advanced safety features with a minimal or zero impact on dimensions or performance. Every Lab can be configured in 3 different bottom-cap-to-battery contact modes with different safety / performance characteristics (Springless-Fused, Springless-Direct and Spring-Loaded). Check out this section for detailed information about each mode.
All devices come with the Springless-Fused contact pre-installed, and include all parts necessary for re-configuration in Springless-Direct mode.
**Important**: All Lab versions retailed after October 1st 2016, do not offer a spring out-of-the-box. It is strongly suggested that the devices are used in fused or direct mode, for performance and safety reasons.
For micro-adjustments of battery space, as in fitting abnormally long batteries, or when using long Kick modules with 18500 batteries, it is recommended that you use a conductive spacer or a spring found in our parts section.
Spare PTC protection modules, silver / rhodium-plated springs (for Spring-Loaded Mode only) and other accessories and add-ons may be selected here or purchased separately.
Features
– Sturdy, refined top-side-mounted switch with silver-plated brass contacts and twist-locking functionality.
– The Lab switch is a smoother, more robust version of our innovative Roller / Dingo switch, a common point of reference for all current top-firing mech designs. All critical components of the new switch are heavily reinforced and 100% liquid-sealed. New switch versions have one twist-locking position (twisting a quarter-circle anti-clockwise) instead of two (older version) due to machining procedure refinements.
– Robust, lightweight 304 food-grade stainless-steel construction with a minimum number of parts for a low-loss, super-efficient operation, unseen in existing top-firing designs.
– Configurable to use a Spring-Loaded, Springless-Fused, or Springless-Direct negative battery connection, for a high-performance or safety-oriented operation.
– Dependable short-circuit protection (Springless-Fused mode) based on a super-low-voltage-drop, resettable PTC element, suitable for resistances down to 0.5 Ohm.
– Hybrid-style, future-proof top connection with open airflow.
– Fits 18650 batteries by mounting a T16 extension
Safety / Performance Configuration Modes
The Lab sets a new standard in mech mod performance and safety, since it has been designed to include advanced safety features with a minimal or zero impact on the overall dimensions or performance of the device. Although IMR batteries are proven to be very safe, every short-circuit results in minor battery damage which affects the discharge characteristics of batteries and their ability to hold a charge. A single, prolonged short-circuit is often enough to cause permanent battery failure.
Out of the box, every Lab can be configured in 3 different bottom-cap-to-battery contact modes with different safety vs. performance characteristics.
Springless-Fused Mode
In Springless-Fused mode, a high-performance protection module is assembled into the bottom cap of the device to protect your batteries and the mod itself from damage caused due to short-circuits. The fuse used in the Lab is resettable (does not “burn”), does not affect the dimensions of the device and has a negligible impact on performance when using resistances down to ~0.5 Ohm.
Overall, the performance of the Lab in the Springless-Fused mode is consistently higher than the performance of most high-end mech devices without any kind of protection built-in.
Springless-Direct Mode
A Springless-Direct cap contact is also included with every Lab, which can be used to remove all protection features from the device. When using the Springless-Direct contact, the voltage drop on the mod will be negligible, resulting in performance unseen in existing top-firing designs.
Spring-Loaded Mode
The Spring-Loaded mode is a compromise between performance and safety. Spring performance is on average higher than the performance of the fuse when using well-maintained and plated or high-conductivity springs. However, it is not as consistent, since springs tend to lose their flex with use.
The spring-loaded configuration is very useful for fitting abnormally long batteries, or when using long Kick modules with 18500 batteries, since it provides around 1.0mm of additional battery space.
**Important**: All Lab versions retailed after October 1st 2016, do not offer a spring out-of-the-box. It is strongly suggested that the devices are used in fused or direct mode, for performance and safety reasons.
For micro-adjustments of battery space, as in fitting abnormally long batteries, or when using long Kick modules with 18500 batteries, it is recommended that you use a conductive spacer or a spring found in our parts section.
Surface Finishing Options
– The BR-M and BR-EM versions are machined from soft brass, a sensitive, “active” material that quickly develops patina on all external surfaces. They are limited-edition, “collectors-only” items, recommended only for skilled vapers with extensive experience in brass maintenance. All Brass batches are small and also are prepared randomly. Stay tuned for availability announcement or contact us directly.
– The SS-IM finish is a dynamic finish. It is not always the same and it gets darker over time. There is no need to worry though, as parts that appear to be different, will eventually look almost identical.
All finishes need cautious handling, but especially sand blasted finishes (SS-IM and BR-EM) are more sensitive to scratches and surface aging.
What's more...
Getting Started
The Lab is a 100% rebuildable, high performance mechanical mod of moderate complexity. It is suitable for experienced vapers who possess a good understanding of the nature of mechanical mods and electric power transfer, but it is also simple and easy enough to be used by intermediate vapers who have the desire to learn the ins-and-outs of their vaping gear in order to get the most out of it.
Mech mods are sophisticated, enthusiast-oriented vaping tools. By nature, a mechanical mod requires:
– Proper handling.
– Frequent maintenance.
Proper handling guidelines are specific to each device. Thanks to its uni-tube design, the Lab is a mod that is very easy to use without requiring constant attention. To help you get up to speed with your new Lab, we have written up a quick reference of 9 Important Tips, which also includes some more general, essential information about mech mods and vaping gear.
Battery / Kick Compatibility
Due to its cap design, the Lab 65 can accept 18650 batteries without any redundant adjustment parts, such as screws or pogo pins, which result in reduced performance and require frequent maintenance.
Check out our Support section here.
Important: The LA-T16 extension limits the battery diameter to 18.40mm max, which means that some (usually low-quality) batteries with thick insulation may not be able to pass through it.
If you are planning to use an Evolv Kick with the Lab, you should be aware that the Evolv Kick 1 / 2 modules are produced with a loose length tolerance: Units with a max length of 17.80mm (2.80mm oversized) may also be found. This means that with certain 18350 battery / Kick combinations, the Kick might not allow the bottom cap of the Lab to close completely, or it may not fit inside the Lab at all. In most cases, the Kick length issue can be remedied by configuring the device in Spring-Loaded Mode. Using the LA-T16 extension in combination with a 18490 battery is another possible workaround.
Use only original, high-drain, low-internal-resistance 18500 batteries such as the AW 18500 IMR.
Warranty and Support
The Lab comes with a fair and generous warranty, which covers all manufacturing defects.
16 reviews for Lab 50
Add a review
You must be logged in to post a review.
You may also like…
Guppy/Lab Parts
VapingTurtle –
If in any doubt, get it!!
The Lab is an absolutely wonderful mod. Smooth, comfortable button; easy locking; perfect hits every time. Simple, clean, and efficient design. I love it!
And to top it off, it comes with wonderful, personal service from the great folks at the Atmizoo team!
With the clean engineering like these folks have shown, I’m really looking forward to the Wave Project.
Scott –
I’ve owned my Lab 50 now for 2 days and all I can say is it’s great, I did buy a Evolv Kick 2 as well but I’m not sure if i need it, it runs my Russian just fine without one (0.7Ω coil) wonderfully!
Atmizoo are great and so are DHL my baby came to me within 24 hours of dispatch to UK
The build quality of this thing is just unbelievable, it just oozes quality every time I press the button, it is expensive but you do get what you pay for and of course if you buy cheap you inevitably buy twice
I cannot say how good this mod is more eloquently than the other reviewers on here so just buy one and you too can have something to cherish – ‘a Greek mod is like a Swiss watch’ something to appreciate into your old age
Just one thing- Atmizoo do some hybrid kits for this mod starting with the Russian (Kayfun 3.1) please
I’ll be back!
David –
Vaping with Lab50 SS is a pleasure and match perfectly with a Kayfun Lite <3
The multi configuration with T16 is cool with MNKE 18650 or AW18490 + Evolv v2 \o/
The adjustment with the bottom cap is the best i've ever seen because it's very quick to change the battery ;-D
I've teste the Icemat version, i'm glad to have a SS version which match better with my atomizers \o/
Many thanks Atmizoo for your great products and your services 😉
Fargazer –
I have owned a Lab 50 Ice Matte finish (at the time called just the Lab) since May of 2014.
– It has been utterly reliable; it has never failed to fire when the button is pressed.
– The adjustable 510 connection works well. Be cautioned, you can only adjust it from the outside, so you cycle through adjust the 510, try the atty, readjust if not right, wash rinse and repeat.
– Very easy to maintain: simple to disassemble, clean, and reassemble. There’s a couple tiny pieces to keep track of if you go as far as disassemble the switch, but instructions from Atmizoo are very clear, and the spare part kit will save you if you do end up losing them.
– The styling is elegant, simple, and functional. Machining is excellent, threading is buttery smooth.
– The PTC protection module is very effective, as I once found out with a shorted atty: no damage to the unit or atty, just a very warm bottom.
– I use Panasonic, Sony, and AW batteries, and I haven’t found any that won’t work with the T16 extension. There are a couple AWs where I have needed to remove the T16 from the Lab, insert the battery into the Lab, then place the T16 back on it. Point is, my Panasonics, Sonys, and AWs all fit :).
– Atmizoo responds quickly to questions, and their shipping reached the USA in three days.
I highly recommend the device, and if my Lab were destroyed or stolen I’d purchase a replacement in a heartbeat.
Kévin –
tout simplement pour moi le plus beau et la meilleur mécanique niveau switch le top du top avec une qualité digne de se nom ,mon premier mods meca et je les toujours greffer a ma main depuis le jour de la réception de se mods high end !!!!!
ATMIZOO le top un grand merci a cette équipe passionnées.
Edwin –
I received the Lab a couple of days ago now and I must say that I still enjoy every second holding this device. It feels so good, it looks amazing and the performance is outstanding! Idon’t think this device can be beaten by something else. Maybe it seems that there are not so much details but in fact there are many. It comes with several different security options and it gives you many options to choose from for your preferred configuration. The quality is superb! Together with my original Kayfun Lite Plus it performs like a beast and this combination looks really stunning. This is probably the best you can buy for the money it costs. I am very happy with the Lab and I would like to thank the whole Atmizoo team.
Carlos –
Es mi primer mod mecánico, por mi trabajo estoy acostumbrado a tratar con herramientas e instrumentos hechos en acero y tengo que decir que este producto es de una calidad magnÃfica, los acabados y el torneado es de un producto de gama alta. Estoy encantado con el mod, en cuanto estén en stock voy a comprar el guppy.
Un último apunte, lo compré el lunes por la mañana, a las 24 horas lo tenÃa en casa.
Muchas gracias.
Maksim –
Simple minimalistic design with great functions.
Top notch service, and blazing fast delivery – placed order on May, 13 and got it in my office in China (!) on May 16. Impressessive!
Waiting for EM Guppy to go back in stock to add to my collection.
Thank you, guys!
Jeffrey –
Wow, can’t be too positive about this mod and the service. I ordered mine may 2 and had it in my hands may 7. Not bad considering I live 6000 miles away in the US. Mod itself is flawless, I ordered SS-IM with the 18650 extension, Looks amazing and mates with my Nautilus perfectly. All the threads are smooth and perfect. Battery fits snugly and solidly. Button fires perfectly and locks easily. Pleasantly surprised at how very compact this mod is and how well it really does perform. Overall the word that comes to mind is “Solid”. Could not be happier with my purchase.
Alan –
Stunning mod.
A very nice, elegant & understated design.
It has a nice weighty feel to it with a battery installed ( similar in weight to a Kayfun Lite+ & Nano kit )
Perfect size for me personally with an 18490 installed. My pinky finger naturally curls inwards, supporting the bottom of the mod.
Brilliant side button ( which suits me perfectly coming from a Vamo ) that isn’t too easy to turn.
The button sits in little notches when it’s rotated +/- 90, so you know exactly whether it is locked or not.
And an adjustable 510 connector, so anything will sit flush on top.
And to top it all off, extremely quick service from Atmizoo too.
Ordered on Saturday lunchtime, picked up on Monday by DHL, and arrived in Scotland on Tuesday.
I only wish I’d thought about the Lab sooner, as I would have saved myself a few £££’s from buying other mods that I wasn’t quite satisfied with.
I’m very satisfied now though, that’s for certain. Thanks Atmizoo.