Lab 35

Features

– Sturdy, refined top-side-mounted switch with silver-plated brass contacts and twist-locking functionality.

– The Lab switch is a smoother, more robust version of our innovative Roller / Dingo switch, a common point of reference for all current top-firing mech designs. All critical components of the new switch are heavily reinforced and 100% liquid-sealed. New switch versions have one twist-locking position (twisting a quarter-circle anti-clockwise) instead of two (older version) due to machining procedure refinements.

– Robust, lightweight 304 food-grade stainless-steel construction with a minimum number of parts for a low-loss, super-efficient operation, unseen in existing top-firing designs.

– Configurable to use a Spring-Loaded, Springless-Fused, or Springless-Direct negative battery connection, for a high-performance or safety-oriented operation.

– Dependable short-circuit protection (Springless-Fused mode) based on a super-low-voltage-drop, resettable PTC element, suitable for resistances down to 0.5 Ohm.

– Hybrid-style, future-proof top connection with open airflow.

– Fits 18500 batteries by mounting a T16 extension.

Safety / Performance Configuration Modes

The Lab sets a new standard in mech mod performance and safety, since it has been designed to include advanced safety features with a minimal or zero impact on the overall dimensions or performance of the device. Although IMR batteries are proven to be very safe, every short-circuit results in minor battery damage which affects the discharge characteristics of batteries and their ability to hold a charge. A single, prolonged short-circuit is often enough to cause permanent battery failure.

Out of the box, every Lab can be configured in 3 different bottom-cap-to-battery contact modes with different safety vs. performance characteristics.

Springless-Fused Mode

In Springless-Fused mode, a high-performance protection module is assembled into the bottom cap of the device to protect your batteries and the mod itself from damage caused due to short-circuits. The fuse used in the Lab is resettable (does not “burn”), does not affect the dimensions of the device and has a negligible impact on performance when using resistances down to ~0.5 Ohm.

Overall, the performance of the Lab in the Springless-Fused mode is consistently higher than the performance of most high-end mech devices without any kind of protection built-in.

Springless-Direct Mode

A Springless-Direct cap contact is also included with every Lab, which can be used to remove all protection features from the device. When using the Springless-Direct contact, the voltage drop on the mod will be negligible, resulting in performance unseen in existing top-firing designs.

Spring-Loaded Mode

The Spring-Loaded mode is a compromise between performance and safety. Spring performance is on average higher than the performance of the fuse when using well-maintained and plated or high-conductivity springs. However, it is not as consistent, since springs tend to lose their flex with use.

The spring-loaded configuration is very useful for fitting abnormally long batteries, or when using long Kick modules with 18500 batteries, since it provides around 1.0mm of additional battery space.

**Important**: All Lab versions retailed after October 1st 2016, do not offer a spring out-of-the-box. It is strongly suggested that the devices are used in fused or direct mode, for performance and safety reasons.
For micro-adjustments of battery space, as in fitting abnormally long batteries, or when using long Kick modules with 18500 batteries, it is recommended that you use a conductive spacer or a spring found in our parts section.

Surface Finishing Options

– The BR-M and BR-EM versions are machined from soft brass, a sensitive, “active” material that quickly develops patina on all external surfaces. They are limited-edition, “collectors-only” items, recommended only for skilled vapers with extensive experience in brass maintenance.All Brass batches are small and also are prepared randomly. Stay tuned for availability announcement or contact us directly.
– The SS-IM finish is a dynamic finish. It is not always the same and it gets darker over time. There is no need to worry though, as parts that appear to be different, will eventually look almost identical.
All finishes need cautious handling, but especially sand blasted finishes (SS-IM and BR-EM) are more sensitive to scratches and surface aging.